約 3,914,938 件
https://w.atwiki.jp/anthony/pages/27.html
玄箱PROパッチ適用 私のようにswat不具合を抱えた玄箱PROを持っている場合は必要になる作業です。ここではTFTPを使用したパッチ適用(ファームウェア・バージョンアップ)です。これもシリアルコンソールなしにはできません。 TFTPサーバー Poor TFTP Server for WIN32をダウンロードして展開 ptftp32.exeを実行 Timeoutは60秒に設定しておく 同じディレクトリにinitrd.buffaloとuImage.buffaloを配置しておく シリアルコンソールからリブートする KUROBOX-PRO ~# reboot PCのアドレスが192.168.1.4でさっき玄箱PROをブートしたときのアドレスが192.168.1.12だったのでserveripにはPCのアドレス、ipaddrには玄箱PROのアドレスを設定 Marvell setenv serverip 192.168.1.4 Marvell setenv ipaddr 192.168.1.12 Marvell tftp $(default_kernel_addr) $(kernel) Using egiga0 device TFTP from server 192.168.1.4; our IP address is 192.168.1.12 Filename uImage.buffalo . Load address 0x100000 Loading ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### done Bytes transferred = 1736612 (1a7fa4 hex) Marvell setenv bootargs $(bootargs_base) $(bootargs_root) rw initrd=0x02000040,20M panic=5 $(buffalo_ver) Marvell bootm $(default_kernel_addr) $(default_initrd_addr) stop_sound ## Booting image at 00100000 ... Image Name Linux-2.6.12.6-arm1 Created 2007-04-10 13 45 13 UTC Image Type ARM Linux Kernel Image (uncompressed) Data Size 1736548 Bytes = 1.7 MB Load Address 00008000 Entry Point 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02000000 ... Image Name initrd Created 2007-04-10 13 46 52 UTC Image Type ARM Linux RAMDisk Image (gzip compressed) Data Size 19286692 Bytes = 18.4 MB Load Address 00000000 Entry Point 00000000 Verifying Checksum ... Bad Data CRC bootm fail. system_not_found Using egiga0 device TFTP from server 192.168.1.4; our IP address is 192.168.1.12 Filename uImage.buffalo . Load address 0x100000 Loading ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### done Bytes transferred = 1736612 (1a7fa4 hex) Using egiga0 device TFTP from server 192.168.1.4; our IP address is 192.168.1.12 Filename initrd.buffalo . Load address 0x2000000 Loading ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## done Bytes transferred = 19286756 (1264ae4 hex) stop_sound ## Booting image at 00100000 ... Image Name Linux-2.6.12.6-arm1 Created 2007-04-10 13 45 13 UTC Image Type ARM Linux Kernel Image (uncompressed) Data Size 1736548 Bytes = 1.7 MB Load Address 00008000 Entry Point 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02000000 ... Image Name initrd Created 2007-04-10 13 46 52 UTC Image Type ARM Linux RAMDisk Image (gzip compressed) Data Size 19286692 Bytes = 18.4 MB Load Address 00000000 Entry Point 00000000 Verifying Checksum ... OK Starting kernel ... arg console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw initrd=0x02000040,20M panic=5 BOOTVER=1.091 CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX --- Uncompressing Linux........................................................ ......................................................... done, booting the kernel. Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #27 Tue Apr 10 22 47 16 JST 2007 CPU ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) CPU0 D VIVT write-back cache CPU0 I cache 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0 D cache 32768 bytes, associativity 1, 32 byte lines, 1024 sets Machine MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 250000000, Tclk = 166664740 Memory policy ECC disabled, Data cache writeback Built 1 zonelists Kernel command line console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw initrd=0x02000040,20M panic=5 BOOTVER=1.091 PID hash table entries 1024 (order 10, 16384 bytes) Console colour dummy device 80x30 Dentry cache hash table entries 32768 (order 5, 131072 bytes) Inode-cache hash table entries 16384 (order 4, 65536 bytes) Memory 128MB 0MB 0MB 0MB = 128MB total Memory 105600KB available (3037K code, 426K data, 112K init) Mount-cache hash table entries 512 CPU Testing write buffer coherency ok checking if image is initramfs...it isn t (no cpio magic); looks like an initrd Freeing initrd memory 20480K NET Registered protocol family 16 serial_initialize_ttyS1 (Debug) ttyS1 is initialized. config_device_cs Error Unknown board CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 128MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PCI0_MEM ....base e8000000, size 128MB PCI0_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB DEVICE_CS0 ....base fa000000, size 2MB DEVICE_CS1 ....base f4000000, size 32MB DEVICE_CS2 ....base fa800000, size 1MB DEV_BOOCS ....base ff800000, size 8MB CRYPTO ENG ....no such Flash bankwidth 1, base ff800000, size 400000 KUROBOX FLASH size 4096[KB] Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_ BOARD_KUROBOX Soc 88F5182 A2 Detected Tclk 166664740 and SysClk 250000000 Marvell USB EHCI Host controller #0 c3403bc0 Marvell USB EHCI Host controller #1 c3403a40 pexBarOverlapDetect winNum 2 overlap current 0 mvPexInit Warning Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI bus0 Fast back to back transfers enabled PCI bus1 Fast back to back transfers enabled SCSI subsystem initialized usbcore registered new driver usbfs usbcore registered new driver hub Use the XOR engines (offloading) for enhancing the following functions o RAID 5 Xor calculation o kernel memcpy o kenrel memzero o copy user to/from kernel buffers Number of XOR engines to use 2 cesadev_init(c00122e4) Fast Floating Point Emulator V0.9 (c) Peter Teichmann. inotify device minor=63 JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. SGI XFS with no debug enabled Serial 8250/16550 driver $Revision 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A ttyS1 at MMIO 0x0 (irq = 4) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized 3 RAM disks of 32768K size 1024 blocksize loop loaded (max 8 devices) Marvell Gigabit Ethernet Driver egiga o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface ** egiga_init_module (10) eth0 Intergrated Sata device found scsi0 Marvell SCSI to SATA adapter scsi1 Marvell SCSI to SATA adapter Vendor Hitachi Model HDT725050VLA360 Rev V56O Type Direct-Access ANSI SCSI revision 03 SCSI device sda 976773168 512-byte hdwr sectors (500108 MB) SCSI device sda drive cache write back SCSI device sda 976773168 512-byte hdwr sectors (500108 MB) SCSI device sda drive cache write back sda sda1 sda2 sda3 sda4 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 physmap flash device 400000 at ff800000 Found SST 39LF020 phys_mapped_flash Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips 1 cfi_cmdset_0002 Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Debug nand_scan nand_flash_ids[i].pagesize is exist Debug nand_scan mtd- erasesize=0x00020000 Debug nand_scan mtd- oobblock=0x00000800 Debug nand_scan mtd- oobsize=0x00000040 NAND device Manufacturer ID 0x20, Chip ID 0xda (ST Micro NAND 256MiB 3,3 V 8-bit) Scanning device for bad blocks Bad eraseblock 854 at 0x06ac0000 Using static partition definition Creating 3 MTD partitions on "nand_mtd" 0x00000000-0x00400000 "uImage" 0x00400000-0x04400000 "rootfs" 0x04400000-0x10000000 "extra" usbmon debugs is not available ehci_platform ehci_platform.4523 EHCI Host Controller ehci_platform ehci_platform.4523 new USB bus registered, assigned bus numb er 1 ehci_platform ehci_platform.4523 irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523 park 0 ehci_platform ehci_platform.4523 USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0 1.0 USB hub found hub 1-0 1.0 1 port detected ehci_platform ehci_platform.16781 EHCI Host Controller ehci_platform ehci_platform.16781 new USB bus registered, assigned bus num ber 2 ehci_platform ehci_platform.16781 irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781 park 0 ehci_platform ehci_platform.16781 USB 0.0 initialized, EHCI 1.00, driver 1 0 Dec 2004 hub 2-0 1.0 USB hub found hub 2-0 1.0 1 port detected USB Universal Host Controller Interface driver v2.2 Initializing USB Mass Storage driver... usbcore registered new driver usb-storage USB Mass Storage support registered. usbcore registered new driver usbhid drivers/usb/input/hid-core.c v2.01 USB HID core driver mice PS/2 mouse device common for all mice md raid0 personality registered as nr 2 md raid1 personality registered as nr 3 md raid5 personality registered as nr 4 raid5 measuring checksumming speed arm4regs 308.800 MB/sec 8regs 217.600 MB/sec 32regs 252.400 MB/sec raid5 using function arm4regs (308.800 MB/sec) md md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 Buffalo Platform Linux Driver(Light) 0.01 installed. MICON ctrl (C) BUFFALO INC. V.1.00 installed. Kernel event proc (C) BUFFALO INC. V.1.00 installed. MICON V2 (C) BUFFALO INC. V.1.00 installed. NET Registered protocol family 2 IP routing cache hash table of 1024 buckets, 8Kbytes TCP established hash table entries 8192 (order 4, 65536 bytes) TCP bind hash table entries 8192 (order 3, 32768 bytes) TCP Hash tables configured (established 8192 bind 8192) NET Registered protocol family 1 NET Registered protocol family 17 md Autodetecting RAID arrays. md autorun ... md ... autorun DONE. RAMDISK Compressed image found at block 0 VFS Mounted root (ext2 filesystem). ---- in linuxrc --- proc mount success libbuffalo mount success -RamdiskRoot- -- linuxrc finished. -- Freeing init memory 112K init started BusyBox v1.2.2 (2007.01.15-11 18+0000) multi-call binary Starting pid 242, console /dev/ttyS0 /etc/init.d/rcS --- rcStart (initrd) --- ===== Starting MountSystemFolders ===== mounting procfs ... [Success] mounting sysfs ... [Success] remounting rootfs ... [Success] mounting all devices ... [Success] --MountNandDevice-- ===== Starting Kevent.sh ===== [Success] ===== Starting networking.sh ===== Deconfiguration network interface lo eth0 killall dhcpcd no process killed create network files.. IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[] killall dhcpcd no process killed route SIOC[ADD|DEL]RT No such process Configuration network interface lo eth0 requesting DHCP tout=30[s] eth0 link down eth0 link up 5 , full duplex 5 , speed 100 Mbps 5 /etc/dhcpc/dhcpcd.exe /etc/dhcpc/dhcpcd-eth0.info new dhcpcd.exe interface eth0 has been configured with new IP=192.168.1.12 hostname is setted to KUROBOX-PRO [Success] ===== Starting sethostname.sh ===== hostname is setted to KUROBOX-PRO [Success] ===== Starting clientUtil_servd.sh ===== Starting clientUtil_server starting on eth0 start at debug mode clientUtil_server Ver.1.01 listen device name = eth0 [Success] Starting pid 484, console /dev/ttyS0 /sbin/getty KUROBOX-PRO login } ログインして更新コマンドを実行する実行 ~ # update_mtd.sh all ***** Cleaning and collect badlist /dev/mtd1 ***** ***** copying /boot/uImage.buffalo to /dev/mtd1 ***** ***** Cleaning /dev/mtdchar2 ***** ***** Writing /boot/nandrootfs.jffs2 to /dev/mtdchar2 ***** ***** copying /boot/u-boot.bin to /dev/mtd0 ***** 480+1 records in 480+1 records out ***** Cleaning /dev/mtdchar3 ***** Done. ~ # リブートする ~ # reboot Orion1 CPU = Low === KURO U-Boot. === ** LOADER ** ** KUROBOX BOARD KURO_BOX LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Apr 10 2007 - 18 10 08) Marvell version 1.12.1 - TINY DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] Flash 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M) Done NAND 256 MB Soc 88F5182 A2 CPU ARM926 (Rev 0) running @ 500Mhz Orion 1 streaming disabled SysClock = 250Mhz , TClock = 166Mhz USB 0 host mode USB 1 host mode PCI 0 PCI Express Root Complex Interface PCI 1 Conventional PCI, speed = 33000000 Net egiga0 [PRIME] Using 88E1118 phy Found boot image hit any key to switch tftp boot. Hit any key to stop autoboot 0 system_bootend Hit any key to stop autoboot 0 Loading from device 0 NULL at 0xfa000000 (offset 0x20000) Image Name Linux-2.6.12.6-arm1 Created 2007-04-10 13 45 13 UTC Image Type ARM Linux Kernel Image (uncompressed) Data Size 1736548 Bytes = 1.7 MB Load Address 00008000 Entry Point 00008000 stop_sound ## Booting image at 00100000 ... Image Name Linux-2.6.12.6-arm1 Created 2007-04-10 13 45 13 UTC Image Type ARM Linux Kernel Image (uncompressed) Data Size 1736548 Bytes = 1.7 MB Load Address 00008000 Entry Point 00008000 Verifying Checksum ... OK OK Starting kernel ... arg console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091 CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX --- Uncompressing Linux........................................................ ......................................................... done, booting the kernel. Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (C odeSourcery ARM 2005q3-2)) #27 Tue Apr 10 22 47 16 JST 2007 CPU ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) CPU0 D VIVT write-back cache CPU0 I cache 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0 D cache 32768 bytes, associativity 1, 32 byte lines, 1024 sets Machine MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 250000000, Tclk = 166664740 Memory policy ECC disabled, Data cache writeback Built 1 zonelists Kernel command line console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BO OTVER=1.091 PID hash table entries 1024 (order 10, 16384 bytes) Console colour dummy device 80x30 Dentry cache hash table entries 32768 (order 5, 131072 bytes) Inode-cache hash table entries 16384 (order 4, 65536 bytes) Memory 128MB 0MB 0MB 0MB = 128MB total Memory 126208KB available (3037K code, 426K data, 112K init) Mount-cache hash table entries 512 CPU Testing write buffer coherency ok NET Registered protocol family 16 serial_initialize_ttyS1 (Debug) ttyS1 is initialized. config_device_cs Error Unknown board CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 128MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PCI0_MEM ....base e8000000, size 128MB PCI0_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB DEVICE_CS0 ....base fa000000, size 2MB DEVICE_CS1 ....base f4000000, size 32MB DEVICE_CS2 ....base fa800000, size 1MB DEV_BOOCS ....base ff800000, size 8MB CRYPTO ENG ....no such Flash bankwidth 1, base ff800000, size 400000 KUROBOX FLASH size 4096[KB] Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BO ARD_KUROBOX Soc 88F5182 A2 Detected Tclk 166664740 and SysClk 250000000 Marvell USB EHCI Host controller #0 c04e4b00 Marvell USB EHCI Host controller #1 c04e4a40 pexBarOverlapDetect winNum 2 overlap current 0 mvPexInit Warning Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI bus0 Fast back to back transfers enabled PCI bus1 Fast back to back transfers enabled SCSI subsystem initialized usbcore registered new driver usbfs usbcore registered new driver hub Use the XOR engines (offloading) for enhancing the following functions o RAID 5 Xor calculation o kernel memcpy o kenrel memzero o copy user to/from kernel buffers Number of XOR engines to use 2 cesadev_init(c00122e4) Fast Floating Point Emulator V0.9 (c) Peter Teichmann. inotify device minor=63 JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. SGI XFS with no debug enabled Serial 8250/16550 driver $Revision 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A ttyS1 at MMIO 0x0 (irq = 4) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized 3 RAM disks of 32768K size 1024 blocksize loop loaded (max 8 devices) Marvell Gigabit Ethernet Driver egiga o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface ** egiga_init_module (10) eth0 Intergrated Sata device found scsi0 Marvell SCSI to SATA adapter scsi1 Marvell SCSI to SATA adapter Vendor Hitachi Model HDT725050VLA360 Rev V56O Type Direct-Access ANSI SCSI revision 03 SCSI device sda 976773168 512-byte hdwr sectors (500108 MB) SCSI device sda drive cache write back SCSI device sda 976773168 512-byte hdwr sectors (500108 MB) SCSI device sda drive cache write back sda sda1 sda2 sda3 sda4 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 physmap flash device 400000 at ff800000 Found SST 39LF020 phys_mapped_flash Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips 1 cfi_cmdset_0002 Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Debug nand_scan nand_flash_ids[i].pagesize is exist Debug nand_scan mtd- erasesize=0x00020000 Debug nand_scan mtd- oobblock=0x00000800 Debug nand_scan mtd- oobsize=0x00000040 NAND device Manufacturer ID 0x20, Chip ID 0xda (ST Micro NAND 256MiB 3,3 V 8-bit) Scanning device for bad blocks Bad eraseblock 854 at 0x06ac0000 Using static partition definition Creating 3 MTD partitions on "nand_mtd" 0x00000000-0x00400000 "uImage" 0x00400000-0x04400000 "rootfs" 0x04400000-0x10000000 "extra" usbmon debugs is not available ehci_platform ehci_platform.4523 EHCI Host Controller ehci_platform ehci_platform.4523 new USB bus registered, assigned bus numb er 1 ehci_platform ehci_platform.4523 irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523 park 0 ehci_platform ehci_platform.4523 USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0 1.0 USB hub found hub 1-0 1.0 1 port detected ehci_platform ehci_platform.16781 EHCI Host Controller ehci_platform ehci_platform.16781 new USB bus registered, assigned bus num ber 2 ehci_platform ehci_platform.16781 irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781 park 0 ehci_platform ehci_platform.16781 USB 0.0 initialized, EHCI 1.00, driver 1 0 Dec 2004 hub 2-0 1.0 USB hub found hub 2-0 1.0 1 port detected USB Universal Host Controller Interface driver v2.2 Initializing USB Mass Storage driver... usbcore registered new driver usb-storage USB Mass Storage support registered. usbcore registered new driver usbhid drivers/usb/input/hid-core.c v2.01 USB HID core driver mice PS/2 mouse device common for all mice md raid0 personality registered as nr 2 md raid1 personality registered as nr 3 md raid5 personality registered as nr 4 raid5 measuring checksumming speed arm4regs 304.000 MB/sec 8regs 215.200 MB/sec 32regs 249.200 MB/sec raid5 using function arm4regs (304.000 MB/sec) md md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 Buffalo Platform Linux Driver(Light) 0.01 installed. MICON ctrl (C) BUFFALO INC. V.1.00 installed. Kernel event proc (C) BUFFALO INC. V.1.00 installed. MICON V2 (C) BUFFALO INC. V.1.00 installed. NET Registered protocol family 2 IP routing cache hash table of 1024 buckets, 8Kbytes TCP established hash table entries 8192 (order 4, 65536 bytes) TCP bind hash table entries 8192 (order 3, 32768 bytes) TCP Hash tables configured (established 8192 bind 8192) NET Registered protocol family 1 NET Registered protocol family 17 md Autodetecting RAID arrays. md autorun ... md ... autorun DONE. Empty flash at 0x00df85f8 ends at 0x00df8800 VFS Mounted root (jffs2 filesystem). Freeing init memory 112K --- rcStart (NANDroot) --- ===== Starting MountSystemFolders ===== mounting procfs ... [Success] mounting sysfs ... [Success] mouting usbfs ... [Success] remouting rootfs ... [Success] mounting all devices ... [Success] ===== Starting checkroot.sh ===== rm /var/lock/perfmon is a directory rm /var/lock/printing is a directory rm /var/lock/subsys is a directory [Success] ===== Starting Kevent.sh ===== [Success] ===== Starting mount_share.sh ===== Mounting /dev/sda4 on /mnt/disk1 as a xfs file system. XFS mounting filesystem sda4 Starting XFS recovery on filesystem sda4 (dev sda4) Ending XFS recovery on filesystem sda4 (dev sda4) Success. Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system. Success. [Success] ===== Starting sethostname.sh ===== hostname is setted to KUROBOX-PRO [Success] ===== Starting networking.sh ===== create network files.. IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[] killall dhcpcd no process killed route SIOC[ADD|DEL]RT No such process Configuration network interface lo eth0 requesting DHCP tout=30[s] eth0 link down eth0 link up 5 , full duplex 5 , speed 100 Mbps 5 /etc/dhcpc/dhcpcd.exe /etc/dhcpc/dhcpcd-eth0.info up dhcpcd.exe interface eth0 has been configured with old IP=192.168.1.12 hostname is setted to KUROBOX-PRO [Success] ===== Starting httpd.sh ===== [Success] ===== Starting telnet.sh ===== [Success] ===== Starting inetd.sh ===== [Success] ===== Starting smb.sh ===== $Starting SMB services $Starting NMB services [Success] ===== Starting clientUtil_servd.sh ===== Starting clientUtil_server starting on eth0 [Success] ===== Starting bootcomplete.sh ===== [Success] ===== Starting FanController.sh ===== [Success] ===== Starting boss.sh ===== ... .. -~~(~~ .~ shDBDhz+(-. .~+sDDBNBDhhszDBNNNNBNNNBDs - ~sBNNNNNNNNNNNNNNNNNNNNNNNNNBs -=DNNBNNNNNNNNNNNNNNNNNBNNNNNNNNBz .~zNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNz~ ~hBNNNNBNNNNNNNNNNNNNNNNNNNNNNNNNNNNNND+ (hNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNBs- .~zNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNBNNBNNNNNNBs ~sBNNNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNNNNNNNz (+DNNNNNNNNNNNNNNNNNNNNNNDzNNNNNhzDNNBNNNNNNNNBs (sNNNNNNNNNNNNNNNNNNNNNNB=~hNNNN=~(sDNNNNNNNNNND (+DNNNNNNNNNNNNNNNNNNNNNNs .=NNNNz- (zDNNNNNNNNNz ~=BNNNNNNNNNNNNNNNNNNNNND- .=BNNNN . .(hNNNNNNNNB ~sNNNNNNNNNNNNNNNNNNNNND+. .+BNNNN+ ~sBNNNNNNN (zNNNNNNNNNNNNNNNNNNNNND ..+BNBNB=- .+BNNNNNNh (zNNNNNNNNNNNNNNNNNNNBB= . hNBBNs+- +DNNNBND (sNNNNNNNNNNNNNNNNNNNND( -DhDBN+ - . =NNNNNB ~+DNNBNNNNNNNNNNNNNNNNz =D=Dhh+( . ~DBNNNB ~(sNNNNNNNNNNNNNNNNNNNz. -hs(zz+ ( . .=NNNNN ~=NNBBBBNNNNNNNNNNNNB= ==-=+s((~. .~BNNNB ~=Nhs +++hNNNNNNNNBz - .~=-.s(+-(- hBNND =Ds+hz( ~hNNNNNNND+ ..-+ .-((( ~ ... -hNNNNDs ~+z(BN=. . BNNNNBhhDD=+ ~. ~-=shBBDhz+( -sBNNNBBNBz ~(=z(BD- ~~hBNNNs~-( zDDs+~(shzssszDBNDh= sBNNNNNNNBN ~~+s z=.-zh~sNNND . . zhhh==shDBNNNNNNNBDDNNNNNNNNNh ~~ ss+ .zBBs~zND+ ..-+zDBNNNNNNNNNNNhzNNNNNNNNND+ ~~(=h +DBz-sBs~ . (BBNNNNNNNNNz- BBNNBNNND= ~(~ zss(( (z sD+ ~DNNNNNNNNNz~ sNNNNNNDs ~(=Ds= ...-(h . . .. BNNNNNNNNz~ -hNNNBh ~(hNs(. =- .=BNNNNNBNs- .(hs== BNz~ . .(hBNNBDz .~ - -hNNh(. .. . (++~ . - . hBNB+ -+( . .- . zDNz( . ~+ - .. . .-. ..~(-. . . .~+(. .. -- . . . + ~ ~. ..... .- . ---(~~~( ~. .. . .((--- -~~(~ . . +s=(- -(+. Let s start a KURO-BOX! .... .(hBDzDD=. and have a fun time... .. .. . sDh+. . .. . ..-- . .. .. ... ....... . . .. .. - .. ... [Success] KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO) KUROBOX-PRO login 最終更新日:2007-05-28
https://w.atwiki.jp/nicoratch/pages/749.html
概要 Vestax PMC-06Pro似のミキサー。フェーダーはALPS製らしい。国内未発売だが島村楽器の自社ブランド SONIC LINEからOEMで販売されていた可能性あり。 +フロント・リアパネル画像 フロントパネル リアパネル スペック表 i channel DJ-audiomixer Zimeless aluminium design (champagne) Excellent audio effects due to well chosen components Long Life ALPS-Crossfader (45 mm) with Reverse control Adjustable Crossfader-Cruve (VGA-control) Long Life ALPS-Linefader (45 mm) Metal potentiometer Double Panel construktion Gain-control with triple sound control per channel Tumbler switch, adjustable in 8 different positions Powerful headphones output External power supply ideal usability due to broad arrangement of the components symmetric XLR-outputs output 1 Master (Cinch, XLR), 2 Line (Cinch) Frequency range 20 Hz - 20 kHz S/N ratio -80dB Distortion factor 0,01% Sound control +15/-32dB Measures 138 x 347 x 87 mm Weight 3kg ■価格 公式HP http //www.reloop.com
https://w.atwiki.jp/prcs/pages/30.html
各種インストール 所要パッケージ/コマンド群/プログラムのインストール KURO-BOX ~# KURO-BOX ~# apt-get install kernel-package ・ ・ ・ KURO-BOX ~# apt-get install kernel-source ・ ・ ・ KURO-BOX ~# apt-get install module-init-tools ・ ・ ・ KURO-BOX ~# apt-get install gcc ・ ・ ・ KURO-BOX ~# apt-get install ncurses-dev ・ ・ ・ KURO-BOX ~# ファイルのダウンロード/更新 所要ファイルのダウンロードソース linux-2.6.25.tar.gz パッチ kurobox-sources-2.6.25.patch ソースの解凍/パッチの適用 KURO-BOX ~# KURO-BOX ~# cd /usr/src KURO-BOX /usr/src# KURO-BOX /usr/src# tar xzvf /usr/lib/cgi-bin/share/linux-2.6.25.tar.gz ・ ・ ・ KURO-BOX /usr/src# cd linux-2.6.25 KURO-BOX /usr/src/linux-2.6.25# KURO-BOX /usr/src/linux-2.6.25# patch -Np1 /usr/lib/cgi-bin/share/kurobox-sources-2.6.25.patch ・ ・ ・ KURO-BOX /usr/src/linux-2.6.25# 所要操作の実行 生成ファイルの更新/同意語の設定/更新前設定利用の明示/設定の更新 KURO-BOX /usr/src/linux-2.6.25# KURO-BOX /usr/src/linux-2.6.25# cp config_kuroboxhg .config KURO-BOX /usr/src/linux-2.6.25# KURO-BOX /usr/src/linux-2.6.25# export ARCH=ppc KURO-BOX /usr/src/linux-2.6.25# KURO-BOX /usr/src/linux-2.6.25# make oldconfig KURO-BOX /usr/src/linux-2.6.25# KURO-BOX /usr/src/linux-2.6.25# make menuconfig ・ ・ ・ カーネルのコンパイル KURO-BOX /usr/src/linux-2.6.25# KURO-BOX /usr/src/linux-2.6.25# make vmlinux ・ ・ ・ KURO-BOX /usr/src/linux-2.6.25# make vmlinux;date KURO-BOX /usr/src/linux-2.6.25# objcopy -O binary vmlinux /boot/vmlinux.bin KURO-BOX /usr/src/linux-2.6.25# cp System.map /boot/ KURO-BOX /usr/src/linux-2.6.25# make modules;date;make modules_install;date KURO-BOX /usr/src/linux-2.6.25# reboot
https://w.atwiki.jp/nicoratch/pages/614.html
概要 2基/3種のフィルターとCFに光学式のインフィナムフェーダーを搭載、14イン/8アウトのFireWireインターフェイスとしても使用可能なミキサー。Traktor® Scratch認証。 スペック表 Premium 4-channel DJ production console with analog VCA circuitry Built-in 14x8 FireWire connectivity for multi-track recording and playback on Mac or PC 45mm Infinium "contact-free" optical crossfader for years of use 2 Onyx premium mic preamplifiers Mackie-designed turntable preamps for ultra-low noise and maximum punch 4 stereo program channels with CD, Phono/Line, and FireWire input select 3-band EQ per channel with complete kill filters and blue backlit knobs 2 "vintage" analog filter FX for on the fly transitions 4 position routing switch per channel for maximum flexibility Additional zone and booth outputs Planet Earth Power Supply--no need for power converters anywhere XLR main outs with mic/line switch for easy stage integration Crossfader features Resistance and Curve controls Advanced cueing section with split cue function Separate mono/stereo booth out True wet/dry stereo aux send for real-time performance FX via analog or fireWire Individual program meters plus main out meters Traktor Scratch certified for live scratching of digital music files on Mac or PC Includes Tracktion 3 Project music production software Compatible with any Windows XP (SP2 or higher) ASIO/WDM host, or Mac OS X Core Audio (version 10.3.9 or higher) Ideal mixer for turntablists, remixers and digital DJs alike d.pro Compatible Software For Recording Tracktion 3 Sonar Cubase Nuendo Logic Digital Performer For Performing Tracktor Scratch (certified) Traktor DJ studio 3 Abelton Live MixVibes PCDJ ¦and many more. ■外形寸法/254(W)×117(H)×393(D)mm ■重量/5.2kg REQUIREMENTS ■Windows/Windows XP(SP2以降)、INTEL Pentium 4またはAMD Athlon XP以上のプロセッサ、256MB以上のRAM ■Mac/Mac OS X(10.3.9以降)、G4以上のプロセッサ、256MB以上のRAM 価格 192,290円(当時) d.4 Pro http //www.mackie.com/jp/products/d4pro/
https://w.atwiki.jp/nicoratch/pages/529.html
概要 高級ヘッドフォンメーカーとして知られるULTRASONE製のDJ用ヘッドフォン。 エージング前と後でだいぶ音質がちがうとか。 スペック表・メーカーサイトより引用 型式ダイナミック密閉型ヘッドフォン ドライバー50mm マイラー 再生周波数帯域10-22,000 Hz インピーダンス64 Ω SPL 出力音圧レベル102 dB 重量295 g (本体のみ) ケーブル長カール3m(6.3mmプラグ) + ストレート80cm(3.5mmプラグ) プラグ形状 付属アダプター ー S-LOGIC テクノロジー 低周波電磁波を98%低減する「ULE」テクノロジー アルミエンブレム 付属品ハードケース スペアイヤパッド 脱着式ケーブル デモCD ■価格 19.000円前後(新品) DJ-1PRO ttp //www.timelord.co.jp/brand/products/ultrasone/dj/dj1pro/
https://w.atwiki.jp/nicoratch/pages/479.html
概要 2012年9月29日(土)発売。Algoriddim djayに最適化されたiPad用DJコントローラー。 2015年1月19日(月)Lightningアダプター対応になりinMusic Japan STORE限定で再発売、現行のLightningコネクターのiPadでも動作可能になりました。 スペック表(メーカーサイトより引用) 電源: ■ ACアダプタ(付属)12V DC2A、Center Pin-Positive iPad : ■ Output Level(XLR):12.8dBV(differential) ■ Output Level(RCA):6.8(single-ended) ■ Frequency Response: +/-2dB、20Hz~20kHz ■ THD+N: 0.03% ■ SNR:105 dB Line In: ■ Output Level(XLR):12.8dBV(differential) ■ Output Level(RCA):6.8dBV(single-ended) ■ Frequency Response: +/-2dB、20Hz~20kHz ■ THD+N: 0.01% Mic: ■ Output Level(XLR):8.2dBV(differential) ■ Output Level(RCA):2dBV(single-ended) ■ Frequency Response: +/-2dB、20Hz~20kHz ■ THD+N: 0.02% ■ SNR:74 dB サイズと重量: ■ サイズ:約565 x 353 x 75mm(W x D x H) ■ 重量:約3.2kg ■価格 50.000円前後(当時) iDJ Pro http //numark.jp/idjpro/
https://w.atwiki.jp/bemaniproleague/pages/10.html
BEMANI PRO LEAGUEとは、「esportsと音楽を融合させたプロリーグ」というコンセプトのもと、コナミアミューズメントが主催する音楽ゲームのプロリーグである。 概要 2020年2月8日、The 9th KONAMI Arcade Championship beatmania IIDX部門 決勝大会終了後、KONAMIからBEMANI PRO LEAGUE(以下BPL)の発足、および2020年5月の開幕が発表。史上初音楽ゲームのプロリーグとして注目を集めた。しかし、同年2月中旬頃からの、世界的な新型コロナウイルス感染拡大を受け、開催は2021年に延期。 開幕に先駆け、2020年夏にBPLのプロモーションとして『BEMANI PRO LEAGUE ZERO』(以下BPLZERO)が開催された。対象機種はbeatmania IIDX。出場する全チームでの総当たり戦や、1試合3戦で1対1でEXスコアの高さを競う形式など、ルールの根幹はこの時点でほぼ完成形に近いものであった。 試合の同時中継等は当時は一切行われず、ドラフト含み全試合がYoutube上での収録配信であった。 2021年春、史上初のBPLとなる『BEMANI PRO LEAGUE 2021』(以下BPL2021)が開幕。アミューズメント施設運営などに携わる企業が参画しチームを結成した。当時の参加企業は、株式会社共和コーポレーション、株式会社レジャラン、株式会社マタハリーエンターテイメント、株式会社ワイ・ケーコーポレーション、株式会社ラウンドワン、株式会社山崎屋の6社。 優勝したチームには賞金2000万円が用意された。 放映については引き続き殆どの試合が収録配信であったものの、ファイナルステージに限りYoutubeにて生配信が行われた。 2021年10月2日、BPL2021ファイナルステージ終了後、コナミアミューズメント執行役員の西村宜隆から、2022年のBPL開催、および対象機種の追加(SOUND VOLTEX、Dance Dance Revolution)が発表された。 2022年1月、KONAMIが『BEMANI PRO LEAGUE -SEASON 2-』(以下BPLS2)の情報を公表。BPL2021から継続参加となる6社に加え、株式会社GENDA GiGO Entertainment、株式会社タイトーの2社の新規参戦を発表した。 同年6月より、BPLS2のbeatmania IIDX部門が開幕。 同部門のファイナルステージについては、プロダクション・レーベルEDP主催の音楽イベント「EDP2022」との同時開催となり、史上初の有観客での開催が実現。生配信も有料チケットを購入することで視聴可能であった。 2022年12月、BPLS2のSOUND VOLTEX部門が開幕予定。 歴代大会一覧 BEMANI PRO LEAGUE ZERO BEMANI PRO LEAGUE 2021 BEMANI PRO LEAGUE -SEASON 2-
https://w.atwiki.jp/nicoratch/pages/1011.html
概要 CDJスタイルのMIDIコントローラー。 各モデル説明 USolo 大型LCDディスプレイと5種のエフェクトを搭載。USBメモリ、MP3使用可能なMIDIコントローラー。 +スペック表・uSolo CDもノートPCも不要 uSoloは、デジタルファイルに対するキュー・再生・マニピュレーション、さらにはスクラッチをも可能にさせる、初めてのUSB対応デジタルミュージック・コントローラです。リアルタイムでエフェクトをかけることもでき、プラグ プレイでMP3ファイルの再生が可能なので起動時間やサーチ時間も全くかかりません。 インテリジェント・ミュージックデータベース・マネジメントシステムにより超高速でトラックのアーティスト/ジャンル/アルバム検索が可能。ピッチ調整は極めて高精度。uSoloはCDプレイヤーでも、コントローラーでもなく、最高のミュージック・メディアプレイヤーなのです。 価格 $249 uSolo http //jp.djtechmart.com/cart-eu/C-MP-uSolo.html USolo mkⅱ 大型LCDディスプレイと5種のエフェクトを搭載。USBメモリ、MP3使用可能なMIDIコントローラー。 +スペック表・mkⅱ Features Professional USB MP3 Player w/Big LCD Display 2 USB ports compatible w/USB 2.0/1.1/1.0 mass storage devices Scratch w/Turntable simulation 5 Adjustable effects FLANGER,FILTER,ECHO,BRAKE,SCRATCH Full Functional CBR VBR bit rate MP3 Playback w/ID3 Tags Auto CUE, Real Time CUE In/ Out/ Reloop (Uninterrupted Seamless Loop Playback) Auto BPM / Tap BPM selectable Fast Track Search Folder Search Adjustable Pitch Percentages +/-6%, +/-12%, +/-25% or +/-100% Multi Mode Giant Jog Wheel for Scratch, Pitch Bend, Search or FX Parameter Magix Audio Cleaning Lab SE Software CD included Dimensions 204(W) x 215(D) x 93(H) mm Weight 1.1 Kgs 価格 $499.00 USolo FX WAV,MP3,USBメモリ利用可能がMIDIコントローラー。BPM同期の3種のエフェクトとキーロック付きピッチコントローラー搭載。 +スペック表・FX USB and SD card input ( SD HC accepted ) Accept most HD up to 250 GB MP3 andWAV compatible TRACK SCAN for direct access to 8 parts of the song Giant Touch Sensitive Jog Wheel with LED CONTROL 2 Scratch mode with 3 Effects 3 HOT CUE with RECALL CUE MEMORY Store 3 CUE per SONG in the mass storage device HD SHARING Share your mass storage device to TWO uSolo FX. DATABOX Software Included Prepare all your files on your computer to manage them quicker on the fly. PLAYLIST Search your files by Artist,Genre,Album and Title. Adjustable AUTOLOOP 3 BPM Sync Effects ECHO,FLANGER,FILTER 100 mm Pitch fader with KEY LOCK Starting/Braking time adjustable MIDI CONTROL with 14 bit High resolution on pitch fader SUPER COMPACT and lightweight Headphones output 価格 349,00 € USolo e 5種のエフェクトとBPMカウンターを搭載したMIDIコントローラー。 +スペック表・e USB input Intelligent music database management Digital turntable platter 5 DSP Effects 4 multi-function jog mode Scratch, FX Parameter, search or pitch Variable Pitch Slider (+/- 6, 12, 25, 100%) and Ultra-precise Pitch Control Firmware upgradeable MP3 s compatible CBR or VBR at any bit rate up to 320kbps Comprehensive realtime looping Seamless Loop can be programmed in real time as well as Reloop Ultra-fast instant start cue point management Auto-BPM counter Dimensions8.03 x 8.46 x 3.66" (204 x 215 x 93mm) Weight2.42 lbs (1.1kg) Packaging Info Package Weight3.95 lb Box Dimensions (LxWxH)11.85 x 11.25 x 5.25" USolo PRO 9種のエフェクトを搭載したMIDIコントローラー。 +スペック表・USolo Pro Mix MP3 Files Twin USB Inputs 9 Effects Combine Effects Comprehensive Interface Large Scratch Wheel /- 6, 12, 25 and 100% Pitch Seamless Looping DJ-Tech http //www.djtechpro.com/eng/
https://w.atwiki.jp/dqwiki/pages/31.html
液晶保護フィルム 液晶保護フィルムは、Surface Pro用のものが使える。なお、Surface RT用やSurface 2用のものは、形状が一部異なるため使用に適さない。 【2013年モデル】ELECOM Surface Pro/Surface Pro2対応 保護フィルム 気泡レス スムースタッチ TB-MSSFPWFLBS 背面保護フィルム 【2013年モデル】ELECOM Surface Pro/Pro2対応 デザインフィルム 背面プロテクト カーボン×ブラック TB-MSP2WRPT1 店頭で購入する場合は、Surface Pro/Surface Pro2用とSurface RT/Surface 2用のパッケージがほとんど同じであるため、型番を確認するとよい。 microSDXCカード 外部メモリ最大対応容量は以下の通り。どれくらい必要か分からないならば、64GBのmicroSDXCカードを買えばよい。 microSDカード microSDHDカード microSDXCカード 2GBまで 32GBまで 64GBまで 【Amazon.co.jp限定】SanDisk Ultra microSDXCカード UHS-I Class10 64GB (無期限保証)[国内正規品] SDSDQU-064G-JAZ キーボード Surface Pro 2にはキーボードが付属しない。キーボードを接続しなくてもタッチパネル上のソフトウェアキーボードで全ての操作が行えるが、文章を入力するならばキーボードを別途用意するとよい。 専用のキーボードとして、薄型の「Touch Cover 2」と、ノートPC用キーボードの感覚で使える「Type Cover 2」が発売されている。キーボードを見なくてもキー入力できるくらいPCに慣れているならば、Type Cover 2を使うとよい。 「2」の付かない「Touch Cover」「Type Cover」は、1世代前のものであり、Surface Pro 2と組み合わせても使用できる。ただし、「2」の付くものの方が改良されている。 マイクロソフト Type Cover 2 N7W-00089 [マゼンタピンク] マイクロソフト 【純正】Surface 2/Pro 2兼用 Touch Cover 2 (ブラック) N3W-00086 もちろん、既に使い慣れているキーボードがあるならば、USBポートにキーボードを接続しても、bluetoothキーボードを接続してもよい。
https://w.atwiki.jp/prcs/pages/28.html
pukiwiki/samba/locales/USBメモリ関連ソフトの導入usbmountはまともに動かない模様・・・ KURO-BOX ~# KURO-BOX ~# apt-get install php5 ・ ・ ・ KURO-BOX ~# KURO-BOX ~# apt-get install samba ・ ・ ・ KURO-BOX ~# KURO-BOX ~# apt-get install smbclient ・ ・ ・ KURO-BOX ~# KURO-BOX ~# apt-get install locales ・ ・ ・ KURO-BOX ~# KURO-BOX ~# apt-get install usbmount ・ ・ ・ KURO-BOX ~# KURO-BOX ~# apt-get install ntfs-3g ・ ・ ・ KURO-BOX ~#